Are you ready to conquer the great outdoors? Whether youre a professional or a hobbyist, youll need a dependable chainsaw to get the job done.
However, the first step is to get it started.
In this guide, well walk you through the steps you need to take to get your chainsaw ready.
Well guide you through checking the spark plug wire, adding fuel and oil, checking the chain tension, and more.
Read on to find out how to get your chainsaw started and get your projects underway!
Table of Contents
Short Answer
To get a chainsaw started, you will need to make sure it is properly fuelled up.
Then you’ll need to pull the starter rope several times until the engine starts.
Once the engine is running, you should pull the choke lever to the “closed” position and press the throttle trigger to keep the engine running.
Finally, move the choke lever to the “open” position and the chainsaw should be ready to use.
Check the Spark Plug Wire
Making sure the spark plug wire is connected is an essential step in getting your chainsaw started.
The spark plug is a small electrical device located near the cylinder of the engine.
It has a wire that is connected to the ignition system and is responsible for igniting the fuel/air mixture inside the engine.
To ensure your chainsaw is ready to start, you must make sure the spark plug wire is securely connected to the spark plug.
Inspecting the spark plug wire is an easy task.
First, locate the spark plug and inspect the wire connection.
It should be firmly attached to the spark plug, with no fraying or corrosion visible.
If the wire is loose or damaged, replace it with a new one before attempting to start the chainsaw.
Once you’ve verified that the spark plug wire is connected, you can move on to the next step in the starting process.
If the spark plug wire is not connected, your chainsaw won’t have the spark it needs to ignite the fuel/air mixture and start.
So make sure you check the spark plug wire first before attempting to start your chainsaw.
Adding Fuel and Oil
Adding fuel and oil is an important step in getting your chainsaw started.
The amount of fuel and oil required depends on the type of chainsaw you have, so make sure you check the manufacturers instruction manual before adding fuel and oil.
If you are using a two-stroke engine, you need to mix the fuel and oil together in a fuel canister.
The ratio of fuel to oil depends on the type of chainsaw and engine you have, so make sure you read the instruction manual for the exact ratio.
Once the fuel and oil have been mixed, pour the mixture into the fuel tank of the chainsaw.
For four-stroke engines, you can use either a fuel canister or a pre-mixed fuel.
If you use a pre-mixed fuel, make sure you use a fuel that is recommended by the engine manufacturer.
Once you have chosen the fuel, pour it into the fuel tank of the chainsaw.
After that, you need to add oil.
Depending on the type of chainsaw, the oil may need to be mixed with the fuel or added separately to the oil tank.
Again, make sure you check the manufacturers instruction manual for the correct ratio of oil to fuel.
Adding fuel and oil is an important step in getting your chainsaw started.
Make sure you follow the manufacturers instructions carefully to ensure that your chainsaw is properly lubricated and that it will start reliably.
Checking the Chain Tension
When it comes to getting your chainsaw started, one of the most important steps is checking the chain tension.
This is essential for safety reasons, as having too much or too little tension can cause the chain to snap and cause serious injury.
The chain should be tight enough that it wont slip or stretch, but not so tight that its difficult to move.
To check the chain tension, you should use a chain tension adjuster tool.
This tool can be found at most hardware stores and is the best way to get the right tension.
Place the tool on the chain and then turn the tension adjuster until the chain is tight.
If the chain is too loose, turn the adjuster clockwise to increase the tension.
If the chain is too tight, turn the adjuster counterclockwise to decrease the tension.
You should also check the chain for any damage or wear before starting the chainsaw.
Look for any cracks or chips in the chain, as well as any worn or missing teeth.
If the chain is damaged or worn, it should be replaced before using the chainsaw.
Finally, make sure the chain is properly lubricated.
Chainsaws use bar and chain oil to keep the chain lubricated and reduce friction.
This oil should be applied to the chain before every use, and should be regularly checked to ensure its not too low.
By following these steps, you can ensure that your chain is in the best condition possible, and that youll be able to get your chainsaw started without any issues.
Pulling the Starter Cord
The most important step in getting your chainsaw started is pulling the starter cord.
Depending on what type of chainsaw you have, you may be working with a two-stroke or four-stroke engine.
If you are using a two-stroke engine, you must first press the primer bulb several times before pulling the cord.
This will draw fuel into the carburetor and allow the engine to start.
When pulling the starter cord, it is important to use the proper technique.
You should always hold the cord firmly in your hand and pull it quickly and smoothly.
This will ensure that the engine starts on the first pull.
When pulling the cord, make sure to stand behind the chainsaw to avoid any kickback from the chain.
If the engine does not start after the first pull, you may need to check the spark plug wire to make sure it is connected properly.
You may also need to adjust the choke or add more fuel or oil.
Once these steps have been completed, you should be able to get your chainsaw started by pulling the starter cord again.
Priming the Two-Stroke Engine
Getting a two-stroke engine running can be a bit trickier than a four-stroke engine, but it’s still not too difficult.
Before you start, make sure the spark plug wire is connected and the chain tension is correct.
Then, you need to add fuel and oil to the chainsaw’s tank.
This is usually a mix of gasoline and two-stroke oil, but it’s important to check the owner’s manual for the exact ratio.
Once the tank is full, you’ll need to press the primer bulb several times until fuel starts to run through the carburetor.
This is called “priming” and it helps get the two-stroke engine ready to start.
Once you’ve primed the engine, you’ll need to set the choke and then pull the starter cord firmly.
You should hear the engine begin to crank and if everything is working correctly, it will start up.
With these steps, you should be able to get your chainsaw started.
Setting the Choke
Setting the choke on a chainsaw is an important step in getting it started.
The choke is a valve that helps to regulate the air-fuel mixture in the engine of the chainsaw.
It is usually found near the carburetor and can be manually controlled.
When setting the choke, the main goal is to ensure that the engine gets enough fuel, but not too much.
In most cases, the choke should be set to the on or run position when the engine is cold, and to the off or stop position when the engine is warm.
This will help to prevent the engine from flooding and make it easier to start.
When setting the choke, it is important to make sure that the switch is in the correct position for the temperature of the engine.
If the choke is set to the on position when the engine is warm, it can cause the engine to flood and not start.
On the other hand, if the choke is set to the off position when the engine is cold, the engine will not get enough fuel and will not start.
It is also important to make sure that the choke is in the correct position when you are ready to start the chainsaw.
If the choke is in the off or stop position, the engine will not get enough fuel and will not start.
On the other hand, if the choke is in the on or run position, the engine will get too much fuel and may flood and not start.
To ensure that the choke is correctly set, it is important to follow the instructions in the owners manual for your particular chainsaw.
This will help to ensure that the engine gets the correct amount of fuel and air, which will make it easier to start.
Pulling the Starter Cord Again
Once you have followed the previous steps in the guide, it is time to pull the starter cord again.
This will begin the process of starting your chainsaw, but you may need to repeat the process several times if the engine is cold.
When pulling the starter cord, it is important to pull it firmly but not too hard.
Too much force can cause the cord to break, which will leave you with a non-functioning chainsaw.
It is also important to maintain a steady motion when pulling the starter cord and not jerk it, as this can put a strain on the starter system.
If your chainsaw uses a two-stroke engine, you will need to press the primer bulb several times before pulling the starter cord.
This will ensure that fuel is delivered to the engine and it will help to get the engine started quickly.
Once you have pulled the starter cord and the chainsaw is running, you should not allow it to idle for too long as this can cause the engine to overheat and damage it.
Instead, you should use the chainsaw for its intended purpose right away.
By following the steps in this guide, you should be able to get your chainsaw started quickly and easily.
With regular maintenance and proper use, your chainsaw should provide you with many years of reliable service.
Final Thoughts
Getting your chainsaw started doesn’t have to be a difficult process.
By following these steps, you should be able to get your chainsaw running in no time.
Make sure to check the spark plug wire, add fuel and oil, check the chain tension, pull the starter cord, prime the two-stroke engine, and set the choke.
Now that you know how to get your chainsaw started, it’s time to put the knowledge to use and get your chainsaw up and running!