Having a hot tub can be an incredibly relaxing and enjoyable experience, but it can quickly become a nightmare if you have to deal with a malfunctioning jet.
If you’re having difficulty removing hot tub jets, don’t worry! This step-by-step guide will provide you with the information and tips you need to successfully remove the jets in no time.
From turning off the power and draining the water to lubricating the jet body and re-installing it, this guide will walk you through the entire process.
So, if you’re ready to get started, let’s dive in!
Table of Contents
Short Answer
Firstly, turn off the power to the hot tub and drain the water.
Then, remove the jet face by either unscrewing or prying it off, depending on the model.
Next, remove the jet body from the wall of the hot tub by unscrewing the nuts that hold it in place.
Finally, remove the jet and discard it.
Turning Off the Power & Draining the Water
Removing hot tub jets is a relatively simple process, but its important to take the proper safety precautions before beginning.
The first step is to turn off the power to the hot tub and drain the water.
This can be done by switching off the main power switch or circuit breaker, or by using a hot tub-specific switch.
Once the power is off, you can begin draining the water.
This can be done with a garden hose or by using the built-in pump.
If using a garden hose, be sure to move it away from the hot tub while draining to avoid submerging it in the water.
If using the built-in pump, you will need to locate the drain plug and remove it to allow for the water to escape.
Once the water is drained, you are ready to begin the jet removal process.
Unscrewing the Jet Faceplate
When it comes to removing hot tub jets, the first step is to unscrew the jet faceplate.
This is usually done by using a screwdriver, although some models may require a hex wrench or other tool.
Once the faceplate is unscrewed, it should come off easily and you can access the jet body.
Be sure to keep track of the screws so you can easily replace them later.
If youre having trouble removing the screws, try using a bit of lubricant or WD-40 to help loosen them.
When youve successfully removed the faceplate, you can move on to the next step.
Unscrewing the Jet Body
Once the power is turned off to the hot tub and the water is drained, unscrewing the jet body is the next step in the process.
Depending on the type of jets installed in the hot tub, there are a few different ways to go about this.
In most cases, the jet body is held in place with screws or bolts.
These screws or bolts are usually located around the perimeter of the jet faceplate.
Using a screwdriver or a wrench, unscrew the screws or bolts holding the jet body in place and carefully remove the jet body.
It is important to take care when unscrewing the jet body, as it can be easily damaged if not handled properly.
Be sure to pay attention to the orientation of the jet body, as this will be important for when it comes time to re-install the jet.
After the jet body has been removed, inspect it for any damage or wear and tear.
If the jet body is in good condition, set it aside and move on to the next step.
Removing the Jet
Removing the jet is the most important part of the process when it comes to replacing hot tub jets.
It is important to ensure that the power is turned off to the hot tub before beginning the process.
Once the power is turned off and the water is drained, the jet faceplate can be removed by unscrewing it from the side of the hot tub.
Depending on the type of jet, you may be able to unscrew the jet body from the faceplate or you may need to use a tool such as a flathead screwdriver or a pair of pliers to loosen the jet body.
Once the jet body is removed, it is important to clean the area around the jet to ensure a tight fit when replacing the jet.
If necessary, lubricate the jet body with lubricant or silicone to ensure a tight seal when replacing the jet.
Once the area is clean and the jet is lubricated, the jet body can be re-installed and the faceplate can be re-attached.
Finally, turn the power back on and enjoy your newly replaced hot tub jet.
Cleaning the Jet & Surrounding Area
When it comes to removing hot tub jets, it is essential to thoroughly clean the jet and the area around it.
This will help ensure a tight fit when it is time to replace the jet.
The cleaning process can be done using a damp cloth to wipe away any dirt and debris.
If necessary, a mild soap and water solution can be used to help remove stubborn dirt and grime.
It is important to make sure the jet and the area around it is completely dry before replacing the jet.
If there is any moisture, it could cause the jet to not fit properly or even damage the jet.
After cleaning the jet and the surrounding area, it is important to lubricate the jet body with a light lubricant or silicone.
This will help ensure a smooth fit when re-installing the jet body and faceplate.
Lubricating the Jet Body (If Necessary)
Once the jet body has been unscrewed and removed, it may be necessary to lubricate it before re-installing it.
Lubricating the jet body helps to ensure a tight seal and a smooth flow of water.
It also helps to reduce the risk of corrosion and wear.
When lubricating the jet body, it is important to use the right type of lubricant.
A silicone-based lubricant is often the best choice, as it is designed to withstand the high temperatures and chemical compositions found in hot tubs.
Be sure to use a silicone-based lubricant that is specifically made for hot tubs.
When applying the lubricant, be sure to cover the entire jet body, including the threads.
Start by applying a thin layer of lubricant to the threads, and then apply a generous amount to the body of the jet.
Be sure to spread the lubricant evenly so that it coats the entire jet body.
Once the lubricant has been applied, it is time to re-install the jet body.
Start by screwing the jet body back into the hot tub, being sure to tighten it securely.
Once the jet body is in place, re-install the faceplate, and turn the power back on.
With these easy steps, you can quickly remove and replace hot tub jets.
Re-Installing the Jet
Once the jet has been removed it is time to reinstall it in the hot tub.
This process is relatively straightforward but it is important to take care to ensure a tight fit and that the jet is properly installed.
First, apply a small amount of lubricant or silicone to the jet body to ensure a tight fit when it is time to insert the jet into the hot tub.
Next, insert the jet body into the hole and secure it in place with the screws.
Make sure to tighten the screws firmly to ensure the jet is firmly in place.
Once the jet body is secured in place, replace the jet faceplate.
This is important to ensure the jet is properly functioning and to keep dirt and debris from entering the hot tub.
Place the jet faceplate over the jet body and secure it in place with the screws.
Make sure to tighten the screws firmly to ensure the faceplate is firmly in place.
Once the jet is reinstalled, turn the power back on to the hot tub and run the water.
Make sure to inspect the jet to ensure it is functioning correctly and that there are no leaks.
If all is well, your hot tub jet is properly installed and you can enjoy your hot tub!
Final Thoughts
With this step-by-step guide, you now have the necessary tools to remove and replace hot tub jets.
All it takes is a few simple steps and a few common tools, and you can quickly and easily remove and replace hot tub jets.
So, what are you waiting for? Get out there and get started on your hot tub jet removal and replacement project today!