How To Fix Lawn Mower Pull Cord? (SIMPLE STEPS)


If youre like most homeowners, you know that a well-maintained lawn is essential for keeping your home looking its best.

But when your lawn mowers pull cord breaks, it can seem like a daunting and expensive repair.

Fortunately, replacing the pull cord on a lawn mower is a relatively simple process that can be done in a few easy steps.

In this article, well explain how to fix your lawn mowers pull cord, including how to locate the recoil assembly, remove the broken cord, and replace it with a new one.

Short Answer

To fix a lawn mower pull cord, first check to make sure the cord is not broken.

If it is broken, replace the cord with a new one.

Next, make sure the cord is properly re-threaded through the pulley system.

Finally, make sure the tension spring is connected to the cord and fully engaged.

If the cord is properly re-threaded and the tension spring is in place, the pull cord should be functioning correctly.

Disconnect the Spark Plug Wire

Before you can begin to fix your lawn mower pull cord, you must first disconnect the spark plug wire.

This is an important safety measure to avoid any potential electric shock while working with the recoil assembly.

To do this, locate the spark plug wire and use a spark plug wire remover tool to remove it from the spark plug.

Once the spark plug wire is disconnected, it’s time to locate the recoil assembly.

The recoil assembly is a cylindrical device that houses the pull cord and is usually located at the top of the engine.

To access the recoil assembly and remove the cover, you’ll need to remove any screws that are holding it in place.

For most models of lawn mowers, this will just require a Phillips head screwdriver.

Once you have the screws removed, you can carefully lift off the recoil assembly cover and access the pull cord.

Locate the Recoil Assembly

Locating the recoil assembly is the next step in repairing a lawn mower pull cord.

The recoil assembly is the device that houses the pull cord and is usually located at the top of the mower near the handle.

It is typically a plastic housing that is round or oval in shape and has a cover on top.

It is usually connected to the mower frame by two screws.

Before beginning the repair, it is important to disconnect the spark plug wire and move it out of the way to avoid any accidental electric shocks.

Once the spark plug wire is disconnected, locate the recoil assembly.

It may be necessary to remove the cover of the recoil assembly to gain access to the pull cord.

This can be done by unscrewing the two screws which hold the cover in place.

Once the cover is removed, the pull cord and its housing should be clearly visible.

It is important to make sure the spark plug wire is out of the way and not in contact with any metal components.

This ensures that there is no risk of electric shock during the repair.

Remove the Cover

Once the spark plug wire has been disconnected and the recoil assembly has been located, it is time to remove the cover of the recoil assembly.

This is an important step, as it allows access to the pull cord so that it can be replaced.

To remove the cover, first find the screws or bolts that are holding it in place.

These should be located near the outer edge of the recoil assembly, and they are typically either Phillips or flat-head screws.

After all of the screws have been removed, carefully lift and remove the cover, being careful not to damage any of the internal components.

Once the cover is removed, the broken pull cord and its winding mechanism will be visible, and ready for replacement.

Remove the Broken Cord

Removing the broken cord is an important step in fixing your lawn mower pull cord.

To do this, you’ll need to locate the recoil assembly, the device which houses the pull cord.

It’s usually located at the back of the mower, near the engine.

Once you’ve located the recoil assembly, you’ll need to remove the cover.

This is usually a plastic or metal casing that covers the pulley and other components of the recoil assembly.

Once the cover is removed, you’ll be able to access the broken pull cord and replace it with a new one.

Be sure to take note of how the cord is routed before you begin, as this will help you with the reinstallation process.

Once the broken cord is removed, you can discard it and replace it with a new one.

Replace with a New Cord

Once you have located the recoil assembly, you can start to replace the broken pull cord.

First, you will need to remove the cover of the recoil assembly.

This can be done by unscrewing the screws or bolts that are holding it in place.

Then, you will need to carefully remove the broken cord and discard it.

Next, you will need to measure a new cord to the correct length.

The cord should be long enough to reach the handle and have enough slack to wrap around the pulley.

After you have measured the cord, you can attach it to the handle.

Make sure to knot the cord securely to the handle and ensure that it is not too tight.

Finally, place the new cord into the recoil assembly and reattach the cover.

Make sure to tighten the screws or bolts securely to keep the cover in place.

With these simple steps, you can easily fix your lawn mower pull cord.

Reassemble the Recoil Assembly

Reassembling the recoil assembly is the last step to fixing a lawn mower pull cord.

It is important to reassemble the recoil assembly correctly to ensure the pull cord operates properly.

The first step is to inspect the recoil assembly for any signs of damage, such as broken or missing parts.

If any parts are broken, replace them with new ones before continuing.

The next step is to reattach the new pull cord.

Start by tying a knot at the end of the cord and thread the cord through the pulley wheel.

Then, wrap the cord around the pulley wheel several times, making sure to keep the cord taut.

The final step is to reinstall the recoil assembly cover.

Make sure all the screws are tight and secure, then reconnect the spark plug wire.

Now, your lawn mower pull cord is ready to use!

By following these simple steps, you can easily fix your lawn mower pull cord.

With the right tools and a bit of patience, you can have your lawn mower running like new again in no time.

Reconnect the Spark Plug Wire

Once the recoil assembly is reassembled, it’s time to reconnect the spark plug wire.

This is a crucial step in the repair process, as the spark plug wire is the source of power for the lawn mower.

To reconnect the spark plug wire, begin by locating the spark plug end of the wire.

This metal end should be firmly attached to the spark plug, which is typically located near the air filter.

Once the spark plug end is located, simply attach the other end of the wire to the appropriate terminal on the mower’s engine.

It’s important to ensure the wires are tightly secured, as a loose connection can cause the mower to malfunction.

After the spark plug wire is reconnected, double-check all of the connections to make sure everything is secure.

Once you’re sure everything is in place, you can start up the mower to ensure it runs properly.

Final Thoughts

Fixing your lawn mower pull cord doesn’t have to be a headache! With these simple steps, you can easily get your lawn mower up and running in no time.

So why wait? Get out there and start fixing your lawn mower pull cord today!

James Lopez

James Lopez is a lifestyle journalist. In addition to working as a journalist, he also takes courses in landscape design. He is pretty focused on the outdoor space, especially the backyard.

Recent Posts